collet
US
・UK
A1 初級
n.名詞寶石座
影片字幕
布宜諾斯艾利斯美食之旅 ?| 離開阿根廷前吃牛排、披薩 + 米蘭薩✈️。 (Buenos Aires FOOD TOUR ? | Eating STEAK, PIZZA + MILANESA Before Leaving Argentina ✈️)
16:16
- there and it tends to be a thicker cut like a thicker thicker than the collet
那裡，它往往是一個較厚的切口 就像比筒夾更厚
亞當-薩維奇的迷你金庫門製作！(第二部分） (Adam Savage's Miniature Vault Door Build! (Part 2))
36:25
- Volt! Volt! Hi, hi everybody. I don't know whether this is a new episode or the continuation of the last episode, but when we last left, when we last, when we last left our intrepid hero, and for the purpose of the story, I'm the intrepid hero, I made a ring gear, a modulus half a millimeter, .5 mod metric gear, and it fits, come on, come on, there we go, whew, and so that right there is a reasonable proof of the depth thing, I did a 72 millimeter circle, I have a lot of adjustability in this diameter, because of the way I'm constructing my vault door, and because this relationship of these gears to the ring gear and the relationship of them to the racks that drive the pins, these spur gears will be attached to a separate ring that itself gets attached into the vault door, that will allow me to properly depth them to the racks, and to make sure that they're centered on this guy. But I get ahead of myself, because a new part has arrived in, and I get to play around with a new proof of concept, so this is a rack, and that is just a straight bar with gears on it, and it engages, it engages, yeah, there you go, you see how that works, so on a bank vault, there's a little rack next to each wheel, like that, and yes, I will have to mill away the backside of that rack, and then that rack goes into a pin, one that looks like that, and that is a dowel pin, which means it is hardened steel, and you can buy dowel pins, come on, these, each of these little spur gills, gills, each of these little spur gill, each of these little spur gears, will themselves move a rack outwards, and that rack will be attached to this pin, how you ask, this pin has a six millimeter threaded hole in it, the next construction phase of this is to make, is to take this rack, put it in the lathe, turn down one end to a six millimeter thread, use a die to thread it, yes, and then thread it into this pin, mill off the back, and that will be, so I will eventually have to do this 12 times, but for right now, yes, I just need a measurement, I just need one measurement, let's see here, not a mission critical measurement, it is, I think, yeah, so .2, and it is ., all right, so I just need to move, remove a hundred thou off the backside of that, that's great, how am I going to turn this rack to be round, it is a great question, and there are tools for doing exactly this, when I ordered the rack, I knew I was gonna turn its back end to be a six millimeter diameter, which meant that I wanted square rack, luckily I was able to find eight millimeter by eight millimeter square rack, these are 5C, and these are 3J, 2J, these are 2Js, these are 5Cs, those are both different collet holding systems, and a collet holding system is one in which you have a hole of a specific diameter, and you have some relief slots that as you pull this piece down into its holder, it squeezes those together, and it is a really nice, very reliable, and gentle way to grab something super tightly, I have these by 60 fourths, no, by 30 seconds, I have these set up by 30 seconds, and every collet holder system is a compromise of accuracy for convenience, but they are a wonderful system, and they make them in stranger shapes, like that, there's hex ones, there's hexagonal ones, which I put somewhere, but I bought an eight millimeter square collet, 5C collet holder, come on, there we go, see that, there we go, now I put that in,
伏特伏特嗨，大家好。我不知道這是新的一集還是上一集的繼續，但是當我們上次離開的時候，當我們上次離開的時候，當我們上次離開的時候，我們無畏的英雄，為了故事的目的，我就是那個無畏的英雄，我做了一個環形齒輪，模數是半毫米，.我做了一個直徑為 72 毫米的圓環，這個直徑有很大的可調節性，因為我是這樣構造我的金庫門的、因為這些齒輪與環形齒輪的關係，以及它們與驅動銷釘的齒條的關係，這些正齒輪將被連接到一個單獨的環上，而這個環本身會被連接到保險庫門上，這樣我就可以將它們與齒條適當地深度連接起來，並確保它們位於這個傢伙的
- While that's happening I have worked out a system for making this little part. It begins with a piece cut roughly to size like this that I then where is it there it is that I then chuck into my square holder and at the bottom of this holder is a stop. This is an installable stop for the back of a 5c collet. So I figure out my hero end here and I put it in and I can't put it farther than that. That allows me to make the same cut on every single piece. So then I chuck this back into the lathe and tighten it down. Hang on. I don't need to tighten it. I don't need to how do you say this? I don't need to tighten it to tighten it. I put it in the jaws and I have this set on low so it's very hard to move this and that'll allow me to get my um my wrench for this in and bring it around and with the 5c's like this you'll feel it stop. There you go and now we turn it around.
就在這時，我想出了一套製作這個小零件的方法。首先，我把一個零件大致切成這樣的尺寸，然後把它夾到我的方形夾頭中，在夾頭的底部是一個擋塊。這是一個可安裝的擋塊，用於 5C 夾頭的背面。是以，我在這裡找出我的英雄端，然後把它放進去，我不能把它放得太遠。這樣我就能在每一塊上進行相同的切割。然後我把它放回車床，擰緊。等一下我不需要擰緊它我不需要怎麼說？我不需要擰緊它來擰緊它。我把它放進夾鉗裡，把它調到低檔 這樣就很難移動了 這樣我就能把扳手放進去，把它轉過來好了，現在我們把它轉過來。
