Placeholder Image

字幕列表 影片播放

  • Welcome to the Speedmaster Video Manual.

    歡迎觀看超霸系列 影片指南

  • Positioned on the side of the watch is the crown,

    位於腕錶側邊的是錶冠

  • which is used for setting the time and winding the watch.

    可用於設定時間 並為腕錶上鏈

  • A single full winding per day

    每天為腕錶上滿鏈一次

  • is all that's needed for the watch to function properly.

    即可確保腕錶運作正常

  • To wind the watch,

    若要為腕錶上鏈

  • turn the crown forward until it stops.

    向前轉動錶冠 直至錶冠停止

  • To set the time,

    若要設定時間

  • pull the crown out one click to its furthest position.

    將錶冠拉出到最外側的第1段位置 直至聽到一聲喀嚓聲為止

  • Turn the crown forward or backward

    前後轉動錶冠

  • to move the hour and minute hands to the desired time.

    將時針和分針 移動至所需的時間

  • When the settings are completed,

    設定完成後

  • make sure the crown is in position 1.

    請確保 將錶冠按回至第1段位置

  • The chronograph is used for measuring time periods

    計時裝置可用於

  • of up to 12 hours.

    計時長達12小時

  • To start or stop timing,

    若要開始或停止計時

  • press the upper pusher located at 2 o'clock.

    只需按下位於2點鐘位置的上方按鈕即可

  • To reset the chronograph hands,

    若要重置計時指針

  • press the lower pusher located at 4 o'clock.

    只需按下位於4點鐘位置的下方按鈕即可

  • For ease of reading in low-light conditions,

    為方便在昏暗的環境下讀時

  • the watch's hands and applied indexes

    腕錶的指針和時標

  • are coated with Super-LumiNova

    均覆有Super-LumiNova超螢光塗料

  • which emits a green light.

    可發出綠色亮光

  • The average speed of a moving object

    超霸腕錶可測量

  • can be measured with your Speedmaster

    物件的平均移動速度

  • by using the central chronograph hand

    透過中央計時指針

  • in conjunction with the watch's tachymetric scale.

    和腕錶的測速刻度即可完成測量

  • For example the speed of a car

    例如車輛的行駛速度

  • can be measured over a set distance of 1 kilometre.

    可透過行駛一公里所需的時間加以測量

  • Press the upper pusher located at 2 o'clock

    只需按下位於2點鐘位置的上方按鈕即可

  • to start the measurement.

    開始測量

  • When the car has reached a distance of 1 kilometre,

    當車輛抵達一公里處時

  • press the pusher again to stop the measurement,

    再次按下按鈕以停止測量

  • and read the value on the bezel's scale.

    然後閱讀錶圈刻度上的數值

  • In our case the car has covered the distance in 30 seconds.

    在此例子中車輛在30秒內完成行駛

  • Therefore

    因此

  • it's traveling at an average speed of 120 kilometres per hour.

    車輛的平均行駛速度為每小時120公里

  • Thank you for watching this video manual.

    感謝您 觀看此影片指南

  • We hope you enjoy your Speedmaster.

    希望您喜歡 您的超霸系列腕錶

Welcome to the Speedmaster Video Manual.

歡迎觀看超霸系列 影片指南

字幕與單字

單字即點即查 點擊單字可以查詢單字解釋