Name: 我所打造的最小的水冷電腦已經完成了! (The smallest watercooled PC I've ever built is COMPLETE!)
Uploaded: 2021-01-14T09:45:55.000Z
Duration: 11 min 38 s
Description: 【看影片學英語】數萬部 YouTube 影片，搭配英漢字典即點即查，輕鬆掌握單字發音與用法，長久累積看電影不必再看字幕。

today, we're gonna finish up this piece of crap.

Putties, Beanies, polos Don't take my word for it is.

So just looking description below when you guys find the link.

So this will probably end up being one of those montage type videos of this couple things.

I want to, I guess answer from the comments section of the previous part of this video.

I showed you guys how I'm using the cross flow right up top because it's also working as both a reservoir and a Phil and a drain section, and we'll show you how I'm gonna do that right now.

It's just a humble the distilled water in here for my proof of concept that the loop would work.

The pump did not, as I showed you guys just didn't have enough power.

But fortunately, my good buddies over at performance PC stepped in and sent me the Swift Tech apogee, too.

Gravity drive to which is basically what Swift Tech did here was.

They shoved it on top of one of their copper blocks and but heat sink on top.

I'm still worried about these guys right here on the side that stick out.

That should work if my calculations are correct, which they never really are, so that doesn't mean shit.

I've got to take the whole thing apart because I've got to drain it.

And I've got to remember to peel that off also had to take the motherboard out anyway, or at least mostly have to install my m dot too.

Remember, this was just a temporary mock up.

So just like any other reservoir to get the loop drained, you gotta have Aaron versus air out.

You have to have a Rh coming in, which means we need an inlet and outlet.

And this cross flow rad works perfectly for that.

So what I'm gonna do right now, I'm sure this looks kind of obvious.

I am just going to I have two tubes hooked up to this and you can't just blow into the tube and expect the coolant to come out.

I had a lot of people suggests, Like we should pick up a vacuum and pulled the coin through.

Is it a pool street dealer ad and back out the other side?

It won't force it through the loop for that to work.

This has to be the only outlet has me the only inlet.

But because this is in the same reservoir radiator, technically, reservoir.

Now tilt this up, and that's how we can drain it.

So I had to do this a bit because it's gonna get trapped in all the blocks and stuff, but I'll be able to get pretty much most of it out this way.

So we learned is that the height of the 90 degrees on here made it interfere with the side panel there.

Fortunately, the effigy drive to allows you to sort of rotate these fittings about.

That way I could get a little bit of extra clearance.

Just further shows that even parts that are made for small form factor builds like this can still sometimes be too big because of the overall size of the case that we're dealing with.

All right, so another snag it is billed as it seems to be the same the, uh, unfortunately e v g.

I'm a little disappointed about that because of the fact that it's so small it was gonna give me all kinds of extra room.

Fortunately, have a 650 watt silver stone here.

I think we just got bad luck, but I want to keep going and don't wait for a replacement.

So I'm going to be stealing the one out of the 1800 ex build because I'm gonna be taking these 1800 x parts out of here and probably building something in, like the h 200 or something like that from NZX t.

You know, you guys are probably wondering, like, Wil j.

Why didn't you just use this build then, for your C E s has got 1800 x and stuff in there.

That's because I promised I was gonna do a fully custom water cooled yada, yada, blah, blah, blah.

And I want to keep my word also to one of the reasons why I'm not using this is I really wanted the silver build.

But when they sent me this for review, they didn't have silver yet.

And the problem of black is scratches show up fingerprints skin because it's like a B blasted sort of a sand blasted finish.

Your skin cells and stuff just get all gross and nasty on it.

But now's a better time than ever to just start to take this one apart, put it out to pasture, get that one up and running.

All right, this is about to be straight up.

Looks like everything is going to clear areas we were concerned with.

Now we're going to now Phil, and bleed the system.

Have to take it apart or do anything with it.

字幕列表影片播放

我所打造的最小的水冷電腦已經完成了! (The smallest watercooled PC I've ever built is COMPLETE!)

stuff

sort

stretch

slightly