Placeholder Image

字幕列表 影片播放

由 AI 自動生成
  • Today I'm going to show you how to make a model of the coca cola lorry,

    今天我'要告訴你如何製作可口可樂貨車的模型。

  • it looks fantastic and makes a great Christmas decoration. We're going to need 12 empty Coke cans, 11 plastic bottle tops, 4 kebab skewers,

    它看起來太棒了,並使一個偉大的聖誕裝飾。我們'將需要12個空可樂罐,11個塑料瓶蓋,4個烤肉串。

  • and a tube of super glue.

    和一管超級膠水。

  • First, we're going to use a knife and a pair of scissors to cut off the top and bottom off all our cans,

    首先,我們'要用一把小刀和一把剪刀把所有罐頭的頂部和底部剪掉。

  • and turn them into a flat sheet of tin.

    並把它們變成一張平坦的鐵皮。

  • Be very careful not to cut yourself. You should be able to cut them to size of 9 x 21 cm.

    要非常小心,不要切到自己。你應該可以把它們剪成9×21釐米的大小。

  • Then take the collected out of the tin by running it backwards over the table edge

    然後將收集到的東西從罐子裡拿出來,在桌子邊上倒過來。

  • until its pretty much flat like this.

    直到它像這樣非常平坦。

  • Then using a marker pen and a ruler, we're going to mark out the templates for each part of the lorry.

    然後用記號筆和尺子,我們'要把貨車各部分的模板標記出來。

  • Once we're finished marking out the templates, we're ready to start cutting them out with our scissors.

    一旦我們'完成標記出模板,我們'就可以開始用剪刀把它們剪下來了。

  • Then using a straight edge, we need to fold over the tabs, and bend the tin into shape.

    然後用直角邊,我們需要把標籤折過來,把鐵皮彎成形狀。

  • This piece is going to form the bonnet, roof and windscreen of the cab.

    這塊要形成駕駛室的引擎蓋、車頂和擋風玻璃。

  • Next using a drawing pin we need to pierce a line of holes along the edge of our template

    接下來使用繪圖針,我們需要沿著我們的模板邊緣穿出一條條的孔洞來

  • approximately half a centremeter apart.

    相距約半釐米。

  • Do the same with the side pieces and pierce through holes for the axles as well.

    側片也做同樣的工作,併為車軸也打通孔。

  • You should end up with a small pile like this to make the cab.

    最後你應該用這樣的小堆來做駕駛室。

  • Next using our super glue, we're going to stick the sides to the bonnet, windscreen and

    接下來使用我們的超級膠水,我們'要把側面貼到引擎蓋、擋風玻璃和車窗上。

  • roof section,

    屋頂部分。

  • then glue on the grill, use celotape to hold it all in place while the glue dries.

    然後在烤架上粘上膠水,在膠水乾燥時,用膠帶將其全部固定。

  • Next take the wheel arch, curl it into shape, bend over the tabs and glue it into place.

    接下來取輪拱,捲曲成型,彎過標籤,用膠水粘好。

  • Do the same on the other side and we should now have something which looks like this,

    在另一邊做同樣的工作,我們現在應該有這樣的東西。

  • Started to look pretty cool eh!

    開始看起來很酷,嗯!

  • Next glue the lorry base into position along the bottom edge of the cab, and then add the back panel.

    接著將貨車底座沿著駕駛室的底邊粘合到位,然後再加上背板。

  • Then using a kebab skewer, we're going to pierce through the holes for our axles to make them

    然後用一個烤肉串,我們'要穿透我們的軸的孔,使他們

  • the right size. Next we need to curl the tin for our exhaust by wrapping it around pen

    大小合適。接下來我們需要將排氣用的鐵皮捲起來,用筆把它捲起來。

  • and a kebab skewer, pierce in some cooling holes with a pin, and glue the pieces together.

    和一根烤串,用針刺入一些冷卻孔,然後把它們粘在一起。

  • Then fix to the cab.

    然後固定到駕駛室。

  • And finally glue a bottle top at the back of the base for towing the trailer.

    最後在底座後面粘上一個瓶蓋,用於拖掛車。

  • Apart from the wheels, that's the cab finished.

    除了輪轂,就是駕駛室完成了。

  • Next we're going to cut out and fold all of the pieces for the trailer, piercing holes along the edges, and in 4 lines along the top.

    接下來我們'要把拖車的所有部件剪開並摺疊,沿著邊緣穿孔,沿著頂部4條線穿孔。

  • It should look like this.

    它應該是這樣的。

  • Once we've got all the pieces, its time to start glueing them together.

    一旦我們得到了所有的碎片,它的時間開始膠水他們在一起。

  • Start with the top and sides, followed by the front and back, then add the base.

    先從頂部和側面開始,然後是正面和背面,再加上底座。

  • Then we need to take our axle runners, pierce holes for the wheels, fold them, and glue them onto the base.

    然後,我們需要把我們的軸流道,為輪子穿孔,對摺,然後把它們粘在底座上。

  • We'll also add the side rails now.

    我們'現在也會加裝側軌。

  • Next we need to fold over our bumper unit, stick it together and glue it into place.

    接下來我們需要將我們的保險槓單元折過來,粘在一起,然後用膠水粘好。

  • And finally add the towing hitch at the front.

    最後在前面加裝拖掛。

  • The cab and trailer are now complete, and all we need to do is add the wheels.

    現在駕駛室和拖車已經完成,我們需要做的就是加裝輪子。

  • Take a bottle top and pierce a hole straight through the middle with a pin, then push through

    取一個瓶蓋,用針直接從中間穿一個洞,然後推過去。

  • a small screwdriver to make the hole a bit bigger.

    用一把小螺絲刀把孔弄大一點。

  • Next thread one onto your kebab skewer, push the axle through the holes on your truck, cut it to

    接下來把一個穿到你的烤串上,把車軸從卡車上的孔裡推過去,把它切成

  • length and add the other wheel.

    長度,並增加另一個輪子。

  • Do all the cab and trailer wheels, then cut out some wheel covers and fit them in place.

    做好所有駕駛室和拖車的輪子,然後剪出一些輪罩,並安裝到位。

  • Attach the trailer and the model in now complete.

    連接拖車和模型在現在完成。

  • To make it light up, put inside some LED keyrings and dim the lights.

    要想讓它亮起來,可以在裡面放一些LED鑰匙圈,把燈光調暗。

  • Music

    音樂類

  • Music

    音樂類

  • I hope you enjoyed watching this video, if you want to see other click on the links on the right hand side.

    我希望你喜歡看這個視頻,如果你想看到其他點擊右側的鏈接。

  • the top link will take you to the plans for building this model, I'm going to go and brush my teeth after drinking all that Coke.

    上面的鏈接會帶你到建造這個模型的計劃,我'喝完所有的可樂後要去刷牙了。

  • Thanks for watching

    謝謝你的觀看

Today I'm going to show you how to make a model of the coca cola lorry,

今天我'要告訴你如何製作可口可樂貨車的模型。

字幕與單字
由 AI 自動生成

單字即點即查 點擊單字可以查詢單字解釋