Name: 如何安裝Nest恆溫器 (How To Install Nest Thermostat)
Uploaded: 2020-12-21T18:25:14.000Z
Duration: 2 min 54 s

A quick start guide, a welcome guide, the thermostat, the base plate and the screws.

快速入門指南、歡迎指南、溫控器、底板和螺絲。

You'll log into the Google Home App and follow the on screen instructions.

你將登錄Google Home應用，並按照螢幕上的訓示操作。

If you don't have a Google account already, go to accounts dot google dot com To set it up.

如果你還沒有Google賬戶，請到accounts dot google dot com進行設置。

Open the Google Home App and click the add button.

打開Google Home應用，點擊添加按鈕。

Tap on, Set up new devices in your home, then select your home the apple Now search for your device When you see what are you setting up tap on thermostat?

點擊, 設置新的設備在你的家, 然後選擇你的家的蘋果 現在搜索你的設備 當你看到你正在設置什麼 點擊恆溫器?

Scan the code on the back of your thermostat.

Make sure your heating and or cooling system is working properly.

確保您的加熱和或冷卻系統正常工作。

Before you start, go to your homes breaker box and turn off the switch that controls the power to your heating and cooling system.

在您開始之前，請先到您家的斷路器箱，並關閉控制加熱和冷卻系統電源的開關。

This will protect it during installation.

You can also turn off the main power switch at the breaker box.

你也可以在斷路器箱處關閉主電源開關。

Next, follow the steps in the APP to remove the front of your thermostat and check the type of system you have.

接下來，按照APP中的步驟拆下溫控器的正面，檢查你的系統類型。

Take a picture of the wires with your phone so you can reference it if you need thio.

用手機拍下電線的照片，以便需要時參考。

Now check if your thermostat is connected to thick wires with wire nuts or if it's labeled 1, 10, 1 20 or 2 40 volts.

現在檢查你的溫控器是否連接到帶有導線螺母的粗線上，或者是否標有1、10、1 20或2 40伏的電壓。

If either of these conditions exist, you have a high voltage system, which is not compatible with nest thermostats.

如果存在上述任何一種情況，則說明您有一個高壓系統，與nest恆溫器不兼容。

Do not connect a nest thermostat to these high voltage wires.

不要將nest溫控器連接到這些高壓線上。

If your system is compatible, tap not high voltage to continue.

如果您的系統是兼容的，請點擊不高電壓繼續。

If you purchased a trim kit, you'll need to install it before you install your thermostat.

如果您購買了裝飾套件，您需要在安裝恆溫器之前安裝它。

I have a trim kit and follow the APP instructions.

我有一個修飾套件，按照APP的訓示。

When you attach the base plate and connect the wires, make sure the connector button stays down after inserting each wire.

在安裝底板和連接電線時，請在插入每根電線後，確保連接器按鈕保持向下。

Otherwise, your thermostat may not get enough power, and you won't be able to finish set up next.

否則，你的溫控器可能電力不足，接下來就無法完成設置了。

Remove the battery tab from the back of the display.

Position the display with the Google logo right side up, and push it onto the base until you hear a click.

將帶有谷歌標誌的顯示屏右面朝上，然後將其推到底座上，直到你聽到咔嚓一聲。

Now go to the circuit breaker and turn the power back on.

現在到斷路器處，重新打開電源。

Select your language, then the APP will test the installation to make sure your thermostat is getting enough power.

選擇您的語言，然後APP將測試安裝，以確保您的恆溫器獲得足夠的電力。

Now follow the remaining steps to tell your thermostat a few more things about your system.

現在按照剩餘的步驟，告訴您的恆溫器有關您的系統的一些更多的事情。

 You'll select the mode you want to use when you turn your system on and then you'll connect to WiFi. 

當你打開系統時，你會選擇你要使用的模式，然後你會連接到WiFi。