Placeholder Image

字幕列表 影片播放

已審核 字幕已審核
  • Today I'm going to show you how to make a really cool light bulb vase.

    今天要教大家製作酷炫的燈泡花瓶

  • We're going to use a screw fit light bulb and a wire coat hanger.

    要用到的東西有螺旋燈泡和鐵線衣架

  • We're going to start by putting on eye protection and a thick safety glove.

    首先戴上護目鏡和安全手套

  • Then take a firm grip of the bulb, and using some pliers, remove the contact

    接著緊握燈泡,用鉗子拔除連接

  • at the end off it.

    燈座底部的接點

  • Next take a thin screwdriver, poke it through the hole and smash the glass cap off the end.

    再拿細螺絲起子,穿過洞口將底部的玻璃蓋戳碎

  • Then using our screwdriver we're going to carefully smash through the glass seal,

    然後將螺絲起子小心地從玻離封口

  • into the bulb.

    伸進燈泡裡

  • Next we need to open up the glass hole so its large enough to remove all the loose content inside.

    接下來要開個玻璃孔,大小需足以讓我們清除內部所有的零件

  • Do this slowly and be very careful.

    慢慢來而且要非常小心

  • Then go ahead and empty out the contents.

    接著繼續清空燈泡內部

  • We now have an empty glass bulb vase!

    現在我們就有空玻璃燈泡花瓶了!

  • To make the stand, we're going to cut the hook off our wire coat hanger, and straighten it out.

    然後是支撐架,先把鐵衣架的鉤子切斷,弄直衣架

  • Then we're going to cut it to a length of 60cm and mark it to 5 equal

    再切成60公分並平分成5等分

  • sections of 12cm.

    每一等分12公分

  • Next we need to bend it into a triangle at the points we've marked,

    接著依標示好的每等分折成三角形

  • Then bend up the 12cm upright

    把其中12公分垂直立向上

  • and the 12cm support bar.

    再將另一12公分做成支撐架

  • Next we're going to curl the end of the support bar by either using you're pliers,

    接下來彎曲支架末端,你可以使用鉗子

  • or by wrapping the bar around something until its the right size for the bulb to screw into.

    或者拿個東西讓支架繞著它捲曲,直到燈泡可置入的大小

  • This needs to be a good snug fit as we don't want the bulb to fall out. And there we have it,

    大小要適中,我們不想看到燈泡掉下來。這樣就完成啦

  • Our simple light bulb vase! But if you want to make it really cool, we can actually

    簡單的燈泡花瓶!如果還想更酷,我們可以

  • make it light up, and to do this, we're going to use an LED keyring.

    讓燈泡發光,若要這麼做,就需要有LED鑰匙圈

  • Take it apart, and remove the battery and the LED.

    先把它分解,取出電池和LED燈

  • This one actually has 2 batteries, and they're too big to fit inside the bulb. So we're going to use

    裡面其實有兩個電池,可是太大塞不進燈泡,所以我們用

  • 3 smaller watch batteries taped up end to end instead, with the LED taped on

    3個較小的手錶電池相疊在一起,再把LED燈黏上

  • and bent to form a switch.

    彎曲形成一個開關

  • Next fix this inside the screw connector at the top of the bulb, using some blue tack,

    下一步將它固定在燈泡裡的螺旋接點處,使用藍色萬用黏土固定

  • and we'll use a screwdriver to switch it on an off.

    再用螺絲起子切換開關

  • Remove it to fill the bulb up with water, then put back the batteries and LED,

    取下LED燈再將燈泡裝水,裝好水再把LED和電池放回去

  • and add some flowers!

    最後再放入些花!

  • Thanks for watching

    感謝您的收看

Today I'm going to show you how to make a really cool light bulb vase.

今天要教大家製作酷炫的燈泡花瓶

字幕與單字
已審核 字幕已審核

B1 中級 中文 英國腔 燈泡 等分 螺絲起子 花瓶 電池 鉗子

驚艷全場的禮物自己做:可愛燈泡花瓶 (How to Make a Light Bulb Vase)

  • 14440 631
    劉老   發佈於 2017 年 01 月 04 日
影片單字

返回舊版